USBtinyISP-Arduino bootloader programmer Introduction
This is a USB AVR programmer supported by offical Arduino IDE. Once the Arduino has lost its bootloader for some reasons, use this programmer to reburn the bootloader and save the dead Arduino.
This programmer works really well for ATmega168 and ATmega328 and should work with all the AVR micros supported by AVRDUDE. Both 10-pin and 6-pin targets supported (cable included) ..
2x1A DC Motor Shield for Arduino
This Motor shield for Arduino uses L293 chip which allow to drive two 7-12V DC motors with maximum 1A current each channel. This shield can be directly stacked on standard Arduino Uno and Arduino Mega.
2 way 7-12V motor drive
Up to 1A current each way
PIN 4,5,6,7 are used to drive two DC motors
Support PWM speed control
Input Shield for Arduino Introduction
The upgraded Arduino Input Shield includes a two axis mini joystick (with moment switch) as well as four colored push buttons(Red,Yellow,Blue,Green). The reserved APC220 Radio Data Module(SKU:TEL0005) interface and the Xbee interface is deisgned to facilitate the realization of wireless rocker button controller. The shield can be easily stacked on top of your Arduino boards. It can ..
Mega Prototyping Shield for Arduino Mega Due Introduction
This is a design for an open-source prototyping shield for Arduino Mega. It has tons of cool features, to make prototyping on your Arduino easy. Some assembling and soldering is required!Some assembling and soldering is required!
Reset button up top
Lots of GND and +5V rails
DIP prototyping area makes it easy to add more chips
Out Of Stock
Prototyping Shield for Arduino Introduction
This is the very first prototyping shield for Arduino in the market since 2010. It comes with prototyping area that you can sold led , switch or other components, it also comes with a mini Arduino breadboard that can stick on the prototyping shield that make the project look tidy and fancy. The working area of this protoshield has DIP prototyping area sutiab..
Out Of Stock
Screw Shield for Arduino Introduction
The Arduino-Compatible Screw Shield is a terminal expansion board that can be screwed directly to the terminal on the thread and is reliable and convenient. It can be plugged into the Arduino controller. You can use this shield to save yourself from the bad port connection. Feel secure with this arduino-compatible screw shield.
Screw Shield x2
Xbee Shield for Arduino Introduction
The Arduino XBee shield is designed to meet wireless sensor networks such as wifi, bluetooth 2.0/4.0 and zigbee. The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission. The shield can be directly stack on top of Arduino Uno / Leonardo and Mega. It provides a 5-3.3V voltage converter to allow 3.3V ..
2.8" TFT Touch Shield with 4MB Flash for Arduino and mbed Introduction Add some flavor to your Arduino / mbed project with this large colorful touch screen. This TFT Touch screen is a fantastic shield with big (2.8" diagonal) and 240x320 pixels with individual pixel control which could apply to Arduino and mbed. It also comes with micro SD slot and 4MB flash so you could add it easily to your projects with this 2.8" TFT Touch screen.
2x2A DC Motor Shield for Arduino Introduction
Arduino product family is a great learning platform for electronics, programming and robotics. But most projects at some point require mobility. This Arduino motor shield allows for motor control with Arduino right away. Stack up this shield on your controller and drive 2 DC motors with higher power requirements. Depending on the motor of choice, you can make it fast or handl..
Out Of Stock
2x2A Motor Shield for Arduino Twin Introduction Arduino product family is a great learning platform for electronics, programming and robotics. But most projects at some point require mobility. This motor shield allows Arduino to drive two channel DC motors. It uses a L298P chip which deliveries output current up to 2A each channel. Stack up this shield on your controller and drive motors with higher power requirements. ..
3.5" TFT Resistive Touch Shield with 4MB Flash for Arduino and mbed Introduction
Add some flavor to your Arduino / mbed project with this large colorful touch screen. This TFT Touch screen for Arduino is a fantastic shield with big (3.5" diagonal) and 240x320 pixels with individual pixel control which could apply to Arduino and mbed. It also comes with micro SD slot and 4MB flash so you could add it easily to your projects with this 3.5" TFT Touch scre..
315Mhz RF Shield For Arduino Introduction
This is an Arduino RF shield that works under 315Mhz. 315M hz is widely applied in areas like vehicle monitoring, remote control, home security system, wireless meter reading, guard monitor system, industrial data acquisition system, wireless tag, identification, non-contact RF card, small wireless data terminals, fire safety systems, wireless remote control system, biologica..
4 Channel Relay Shield for Arduino Introduction
This Relay Shield for Arduino acts like a switch. It is commonly used to control anything over 5V such as lamps, water pumps and garage doors. One of the most interesting projects for your boards is perhaps being able to control High power devices like Lamps, water pumps, garage doors and so on. But interfacing with high power and AC is quite a dangerous task when building the ..
6 DOF IMU Shield For Arduino Introduction
This is a 6 Dof IMU shield for Arduino, using the ADXL345 accelerometer and the ITG-3200 gyro.This IMU Combo shield also embeded a xbee sockets. So it's suitable for the projects that need bluetooth, wifi or Zigbee wireless communication.And the shield extends a pair of the encoders, the motor driver interface and 4 analog input connectors.
It's aimed to run on t..
7 Segment LED Keypad Shield For Arduino Introduction
This 7 segment LED Keypad Shield is an Arduino LCD Shield with a 4 digit 7 segment digital tube display (common cathode). It has 5 buttons that can be used as menu select buttons or control buttons, using I2C to drive the digital tube for an easy user experience.
Working voltage: 5V
4 digit 8 segment common cathode digital tube (0.56 i..
Accessory Shield for Arduino Introduction This Accessory Shield for Bluno is specially designed for Bluno (BLE with Arduino Uno), which is first of its kind in intergrating BT 4.0(BLE) module into Arduino Uno. It also compatible with standard Arduino Uno. With Bluno, this Accessory Shield forms an ideal prototyping platform for both software and hardware developers to go wireless. You will be able to develop your own s..